Installation of basin sink

A-Basin sink is an essential accessory in every house, and how to install it properly is an issue you can focus on. Understanding its installation process will allow you to quickly identify problems in future use. Let's take a closer look at how to install a bathroom basin sink.

The following is a list of contents:

• The overall installation of the basin sink

• Connection of basin sink and water pipe

• Installation of basin sink accessories

The overall installation of the basin sink

1. First, remove the root mother, eye ring, and rubber gasket of the drainage port of the basin sink, insert the upper gasket with putty into the hole of the drainage port of the sink and align the overflow port of the drainage port of the basin with the overflow eye of the drainage port of the basin. Outside plus the gasket with good putty, set the eye ring, bring the root mother, and then use a homemade wrench to jam the drainage port crossbar, and use a flat wrench on the root mother to the right degree of tightness.

2. The spout root mother and lock mother were removed, and the root of the spout well-gasketed putty, was inserted into the basin to give water eye. And then set the rubber gasket eye ring below, and put on the root mother after the left-hand press the spout, the right hand with a homemade eight-dead wrench will lock the mother tight to the right degree of elasticity.

3. Should be drawn by the center of the drain mouth in the sink bathroom wall vertical line, from the ground up to measure the specified height, draw a horizontal line, according to the basin width on the horizontal line to draw the crosshairs of the position of the bracket. Tick into a 30×120mm hole according to the mark. Level the basin bracket and plant it firmly. Then place the basin on the bracket to level and square. Hook the rack hook in the fixing hole under the basin, tighten the fixing bolt of the basin rack and find the leveling.

Connection of basin sink and water pipe

1. Connection with S-type water pipe. Should be coated with lead oil at the lower end of the basin drain wire buckle, and wrap a little twine. The upper section of the water storage bend screwed in the drainage port, loose and tight. Then the lower end of the lower section of the water storage bend wrapped in an oil pan root rope was inserted in the sink bathroom drain mouth, the rubber gasket was placed in the connection of the water storage bend, the locking mother hand-tighten and straighten to find the right. Then use a wrench to tighten it to the right degree. Use putty to stuff the downpipe eye tightly and smooth it out.

2. Connection with P-type water pipe. Should be coated with lead oil at the lower end of the basin drain wire buckle, and wrap a little twine. The water storage bend vertical section screwed in the drainage port, the right amount of tightness. Then the water storage bend cross-section according to the required length. Put the locking mother and the mouth guard plate back to back on the cross-section, wrap the oil pan root rope at the end, test the height is appropriate, such as inappropriate available to adjust the vertical section, then put the rubber pad in the lock mouth, the locking mother screwed to the appropriate tightness. Fill the mouth guard plate with putty and then level and press the wall. Remove the overflowing putty and wipe the wall. Clean up the exposed hemp wire at the basin sink downspout.

Installation of basin sink accessories

1. Add a 1mm thick rubber pad and putty to the root of the mixed water spout. Insert it into the middle eyelet along the top of the basin, add the rubber gasket and eye ring at the lower end, hold the spout, tighten the root mother to the right degree of tightness, and bring a good water supply lock mother.

2. The cold and hot water valve covers are removed, back off the lock mother, and the valve from the bottom up into the basin sink cold and hot water orifice. The valve lock mother and rubber ring are set into the four-way horizontal tube, and then the valve on the root mother oil ash and 1mm thick rubber gasket, the root mother tighten, and silk buckle flat. Cover the valve cover, and tighten the door cover screws.

3. Washbasin drainage port plus 1mrn thick rubber gasket, putty, inserted into the washbasin drainage eye, the outside of the rubber gasket and eye ring, the fillet buckle at the oil, wrap hemp. Use homemade wrenches to jam the crossbar of the drainage port, and screw them into the drainage tee port, so that the mouth is backward, and the overflow port aligns with the bathroom basin sink overflow eye.

4. The portable tie rod and spring universal bead into the center of the tee, the lock mother screwed to the right degree of tightness. And then the vertical rod through the mixed water nozzle hollow tube to the four-way under the mouth, four-way, and vertical rod interface wrapped oil pan root rope tighten the compression nut. Stand, cross-road intersection with the card to connect well, while adjusting the positioning.

The above is the installation steps for the bathroom basin sink, understanding the process can let you better use it. The basin sink we provide can be repaired free of charge within the service period, usually have any related questions can visit our official website https://www.njvictor.com/Conduct consultation, look forward to your arrival!